A-80 Power Wire
The 12 gauge red wire on the 2-pin power plug is the 12 Volt positive power wire. It must be connected to the positive terminal of the battery to provide a power source with a low voltage drop and low noise. Do not make the power connection at the fuse block or any point other than the battery. Improper power sources can reduce output and cause distortion.

The fuse holder should be connected to the battery's positive terminal. The fuse is designed to prevent fire or damage to your car, should the battery wire short to ground. Wait to insert the fuse into its holder until all power connections have been made.

If it is necessary to lengthen the battery wire, add the required length between the amplifier and the fuse holder, not the fuse holder and the battery. Use 12 gauge or larger to extend the battery wire. It is best to use as short a wire as possible.

Be sure you DO NOT run the power wire next to the input cables of the amplifier, as this may induce noise.

Avoid running the power wire near the radio's antenna or power leads, or near sensitive equipment or harness. The power wire carries substantial currents and could induce noise.

CAUTION: DO NOT substitute the 15 amp fuse included with the Amplified Bazooka with anything other than the same fast blow current rated fuse. Substitution or deletion will void the product's warranty and may cause damage to you car or the amplifier.

A-80 Ground Wire
The 12 gauge black wire on the 2-pin power plug is the negative ground wire. It must be connected directly to the vehicle chassis near the amplifier.

We do not recommend extending the ground wire in any installation, as this can cause unwanted ground loops.

The ground point in the car should be a piece of chassis metal that is welded to the main body of the vehicle. Painted surfaces should be scraped or sanded clean before the ground lug is bolted down. (Cover the bare metal area with paint or grease to prevent rust.)

top

A-80 Remote Turn on Options
The Orange wire on the Amplified Bazookas' 14-pin Molex Mini-fit Jr. connector is the remote turn on wire. You have several options for connecting the Remote Turn-on.

Option One 12 Volt Remote from source unit with SAS Rocker Switch

Option Two 12 Volt Remote from source unit

Option Three 12 Volt Accessory or ignition with SAS Rocker Switch

Option Four 12 Volt Accessory or ignition

Option Five TA-80's built-in Auto Turn-On Feature

top

A-80 Remote Turn-On Option One
Using an SAS On/Off Switch connect the ORANGE Remote Turn On to one side of this switch, with the other side connected to the source unit's "Accessory," Auto-Antenna," or "Remote" lead -- any of which will supply 12 Volts positive when the source is turned on.

The SAS On/Off Switch allows you to demonstrate to others the difference the Amplified Bazooka makes in your system, or to turn it off whenever you desire.

A-80 Remote Turn-On Option Two
If you don't want the use of the SAS On/Off Switch you may hook up the ORANGE Remote Turn On wire to the source unit's "Accessory," Auto-Antenna," or "Remote" lead -- any of which will supply 12 Volts positive when the source unit is turned on.

This will allow the Amplified Bazooka to be turned on and off with the source unit.

A-80 Remote Turn-On Option Three
If the source unit does not have an Auto-Antenna lead (or if the Auto-Antenna goes down during tape operation) you can connect the Amplified Bazookas' ORANGE Remote Turn-On wire to one terminal of the SAS On/Off Switch and the Switch's other terminal to an accessory or ignition point at the vehicle's fuse block.

In this configuration, the Amplified Bazooka will be on whenever the ignition and the SAS On/Off Switch are both on.

This method may allow noise or turn-on and turn-off transients to become amplified when the source unit is not in use.

If this occurs, simply turn off the SAS On/Off Switch when the source unit is not in use and this noise will be eliminated.

Instructions for Mounting The Switch

top

A-80 Remote Turn-On Option Four
If you don't want the use of the SAS On/Off Switch and the source unit does not have an Auto-Antenna lead, you may hook up the ORANGE Remote Turn-On lead to an accessory or ignition point at the vehicle's fuse block.

This will allow the Amplified Bazooka to be turned on by the vehicles' ignition, and remain on as long as the key is in the accessory of run position.

NOTE: This method may allow noise or turn-on and turn-off transients to become amplified when the source unit is turned on, off or whenever it is not in use and the vehicles' ignition is on, and therefore may prove to be unsuitable for your application.

A-80 Remote Turn-On Option Five
The Amplified Bazooka has a built-in Auto Turn-On Feature.

If you choose to use this feature, the Amplified Bazooka will turn on automatically whenever there is music present at the inputs (high-level or low-level inputs).

Please take notice of the On/Off Jumper Clip located on the back of the amp, right above the harness receptacle.

SAS ships the Amplified Bazooka with this Jumper in the Off Position.

To use the Auto Turn-On Option the Jumper must be in the On Position. The Jumper Clip must be lifted off of the middle and right hand pins and reinserted across the left hand and middle pins to enable the Auto Turn-On feature. This can be done easily with a pair of needle nose pliers. With the Jumper in the On Position, the Amplified Bazooka will turn on automatically when it senses any music.

The ORANGE wire should not be connected to anything if this feature is being used. Be sure to insulate the end of the ORANGE wire so that it will not short to ground, as this may damage the Amplified Bazooka.

top

Mounting The Switch
The SAS On/Off Switch has a variety of mounting options.

Supplied with the switch is a mounting plate for under dash application. Notice that one end of the mounting plate is angled and the other is not.

Select the end that is best suited for your application and mount that end of the plate to the dash panel.

The switch can also be flush mounted into a flat panel or factory switch knock out panel.

Be sure that the place you choose to flush mount the switch has enough clearance behind it before you start the installation of the switch.

Using the supplied mounting panel as a template, etch the mounting hole on to the panel you wish to mount the switch. Carefully cut out the mounting hole.

top

A-80 Input Signal Connections

HIGH-LEVEL INPUTS
If the source unit has only speaker outputs, use the Amplified Bazooka's high-level inputs. If the source unit has both high and low level outputs, we recommend using the high level inputs over the low level inputs, due to the configuration of the TA-80's balanced input circuit. NEVER USE BOTH high and low-level inputs at the same time!

Connect the GREEN wire from the 14-pin Molex plug of the Amplified Bazooka to the source units left (+) positive speaker output. Connect the GREEN W/BLACK stripe wire of the plug to the source units left (-) negative speaker output. Connect the GRAY wire of the plug to the source units right (+) positive speaker output. Connect the GRAY W/BLACK stripe wire of the plug to the source units right (-) negative speaker output. If the source unit has both front and rear speaker outputs, use only one set of speaker outputs for the high-level input of the Amplified Bazooka.

WARNING - Connecting one of the Amplified Bazooka's High-level Input channels out of phase electrically with the other High-level Input channel may cause damage to the amplifier's input section. NEVER DO THIS!

NOTE:
If you are not sure of the polarity of the wires that you are tapping into, connect one channel first and check it by turning on the unit and listening to it.

If there is no output, turn off the unit and reverse the polarity of the inputs wires.

If it still has no output, you have other problems, Check all connections. If it sounds correct, turn off the unit and connect the other channel.

Turn on the unit again and listen to it, if the output increases, you are connected correctly.

If the output drops or is reduced, turn off the unit immediately as it is not the correct polarity and may damage the unit.

Reverse polarity of one channel and check it again, the output should increase which indicates you have the connections correct.

top

LOW-LEVEL INPUT
If your source unit only has low-level RCA phono jack output, use only the low-level inputs of the Amplified Bazooka.

Connect the low-level RCA phono jack inputs of the Amplified Bazooka to the source with a shielded RCA patch cord. To avoid possible noise problems, be sure to run the patch cord away from all power wires and factory wire harnesses.

DO NOT make any connections to the Green and Gray high level wires of the Amplified Bazooka and be sure these wires are insulated to avoid the possibility of a short circuit.

top

A-80 Optional High-Level Output
The Amplified Bazooka has provisions for high level output to a second Bass Tube. If you want to use this feature, you can purchase a Bazooka slave unit from an authorized SAS dealer.

Be sure to use a slave unit that is the same size as you amplified unit. This is necessary because different size woofers have different efficiencies. These efficiency differences result in the two woofers playing at different volume levels, making it difficult to adjust the system to the desired sonic quality.

Located the BROWN and YELLOW wires on the 14-pin Molex plug, connect the BROWN wire to the RED terminal of the slave unit, and the YELLOW wire to the BLACK terminal of the slave unit.

The Amplified Bazooka is now operating under a 2 ohm load and is delivering a total of 120 watts.

top